T. Nexus Engineering Indonesia, An Established Oil and Gas Support and marine Company invites suitable qualified candidates to fill the following position:
Commercial Supervisor
- Female
- Diploma or University graduated
- Able to speak and write mandarin and English
- Good working attitude & Able to work independently with high integrity
- Preferably knowledge computer literate windows / office
- Fresh grads with outstanding academic are welcome
Please Apply Online!
Only short candidate will be notified. Please send your application before 10 May 2008.
I hope join with your company soon
Dear Sir/Madam,
With this letter, allow me to apply for position of Commercial Supervisor in PT Nexus Engineering Indonesia.
I am ismadi,ST, 30 year old, Meried, graduate of Bacelor’s Degrees
Department Mecanical Engineering, Universitas Batam (UNIBA). I was
graduate at 2002 with 2,70 of GPA. I have ability to operate some
computer program like Microsoft office, excel,power point,MS word
As consideration, I enclose also resume of me, and I attach picture in
my resume, working experience.
I hope my qualifications and my ability merit your consideration and
look forward to your reply. I hope I am able to follow carried out
selection steps and also can get away to become an employee at PT Nexus Engineering indonesia
Yours faithfully,
Ismadi,ST
C U R R I C U L U M V I T A E
Experiences
July 2006 – At present PT Sanmina- SCI-Batam
As Senior Asst Engineer Process
Sanmina-SCI is the word wide PCBA manufacturing company
• Yield from SMT ~ Finish good responsibility
• Drive the pilot run as well
• As the leader for the project transfer
• Process improvement
• DFM generation for any deviation design or process capability issue
• Driver of FA (First Article) product, In term of :
• L iase with the customer
• Define the process Flow Chart
• Generate Lot Traveler
• Work Instruction generation (PCB Preparation ~ Packing/Shipment)
• Control of direct and Indirect material
• FA qualification report
• Drive the improvement of Quality (Process capability and defect per million) and Process Yield.
• Drive continuous improvement projects (e.g. cost reduction)
• Provide support on the start-up, set-up and qualification of new incoming equipments and materials before being used by production.
• Responsible in performing process parameters optimization with statistical approach (e.g. Design of Experiment).
• Responsible in setting up the SPC at every critical process point.
• Responsible in analyzing the defective products returned by the customer and perform investigation through an 8-D (8-Discipline)
• Liase with supplier and other Dept as part of continuous improvement
 Working instruction draft and release to production
 ECN follow up and implementation
June 2004 – June 2006 PT PLEXUS MFG Indonsia-Batam
PCBA manufacturing Company
Senior SMT Technician
Responsibilities:
 Controling Spare part to be reported to superrior
 Release/ updating document of standard operation procedure.
 Setup and prepare for new model.
 Handle all SMT document and data collection.
 As the leader for all Technician Incharge.
 Reporting to superrior about pevormance and improvement of the machine and utilization for daily,weekly,mounthly,quarterly and yearly to keep good conditionof the machine according standard ISO 9002.
July 2000 – April 2004 PT. Schneider Electric – Batam
SMT Technician
Responsibilities:
• Incharge and maintenance of machine performance.
• Monitoring of machine performance and throuble shotting
• Maintain of yield as good condition
• Monitoring production machine as whell.
 Setup and prepare for new model.
July 1997 – july 2002 PT. Epson – Batam
SMT Technician
Responsibilities:
• Incharge and maintenance of machine performance.
• Monitoring of machine performance and throuble shotting
• Maintain of yield as good condition
• Monitoring production machine as whell.
 Setup and prepare for new model.
Trainings attended
• PANASERT Chip and IC mounter internal Training 03th–08th July 1997 at PT EPSON BATAM.
• YAMAH Chip and IC mounter internal Training 17th–22th July 2000 at PT EPSON BATAM.
• In House Traning of PLC 26th – 2 th December 2002 at PT.Schneider Electric – Batam
• Juki Chip and IC Mounter Training 12th-17th June 2002 at PT.Schneider Electric – Batam.
• Vitronic Delta Wave Soldering 04th – 09th November 2002 at PT.Schneider Electric – Batam.
• Fuji Chip and IC mounter internal training 20th – 25th August 2004 at PT.PLEXUS MANUFACTURING INDONESIA-BATAM
• Siplace advance level 1 19th – 23 th September 2005 at SIEMENS CENTER – Singapore
Education 2002: Graduate Bachelor’s Degree from ‘’ UNIVERSITY BATAM ‘’ (UNIBA) Department of Mecanical Engineering.
Others
• Fluent in English (Oral and Literal),Malay and Bahasa Indonesia
• Good in Microsoft Office (MS Excel, Power Point and MS Word)
• GC-Prevue
Reference: Mr.Abarques Layag Junell
Snr.Manufacturing Engineer
Hp : +62 813 6498 3466
Phone : +62-770 612 666 Ext 794
Pasport Number AJ-274166
Interest : Sport,Muzik, and General knowledge